MY HEART DRAW A DREAM

新版的Mac OS X 10.5 Leopard才上市沒幾天，還不到一個星期哩
馬上就有國外的Hacker公佈破解了安裝Leopard在PC上
變成了名副其實的「花豹在Intel PC上暈倒」
也發表的安裝教程，引起熱烈的討論
不過這並不是什麼合法的行為
Mac OS被規範只能安裝在Mac上面
就算可以裝在PC上，問題應該也會不少吧，我猜
光是Driver就是一個很大的問題了(?)
而且據已經安裝成功的網友提供的情報看來
Leopard在PC上會有部份功能無法使用
所以想體驗Leopard的，還是乖乖的去買台Mac吧！

我本來也想試試裝在PC上玩玩看
不過我發現要安裝Leopard，CPU必須要有支援SSE3才行
雖然我現在用的這台電腦(Prescott)有支援
但是不可能直接拿這台來安裝，萬一沒裝好我電腦不就不能用了= =
而且Partition還得格式化成HFS+
這部份我都沒用過，很怕出了什麼問題
雖然旁邊還有一台我妹的舊電腦，目前是用不到的
可是太久沒去注意PC的規格了，也忘了那台電腦的CPU是否有支援SSE3
所以後來我還是把這個主意作罷了
等有了Mac再來體驗吧 = =

不過既然都提到這個了
我就也po一下如何把Leopard安裝在PC上的教程吧

安裝Leopard過程中需要以下物件

一個動過手腳的DVD鏡像
一個包含補丁的Zip文檔
一個被格式化為FAT32的閃存

原文出自：Hack Attack : Install Leopard on your PC in 3 easy steps!

附上安裝教程全文，以下：

Step 1. Getting things ready  

Burn the DVD Image onto a Single Layer DVD-R using a software like Nero.
Format the USB Flash Drive and the drive label should be "Patcher" without the quotes. Please note it has to be "Patcher" only and nothing else for the patch to work when we apply it later.
Extract the Zip file and put its contents into the USB Flash Drive.
Now your USB Drive should contain a folder called "files", if it doesn't then check to see where you have gone wrong.


Step 2. Installing Leopard

Now that you have the Patched DVD with you, you can now install Leopard. Pop in the DVD into the drive and boot into it by pressing F12 at the BIOS Prompt.
Boot into the DVD and the installer should now load. It take a while though, so be patient.
Select your Language and make sure you select Customize and you need to deselect all the packages that are displayed.
Leopard will now install. This can take a while, so go grab yourself a coffee.
It will ask you to Reboot, so go ahead and Reboot. Before rebooting make sure that USB Flash Drive is connected to the PC.


Step 3. Patching Leopard

Now that you have got Leopard installed, you need to patch it. Before we do that Boot into the Leopard DVD like the way you did before.
Wait for the Darwin Bootloader to load. Once it loads up press F8. You should now see a prompt. Type -s and hit enter. The DVD will now load in Verbose mode. Watch for any errors. It should load without a problem because you have already installed Leopard.
Once the setup is loaded select your Language. Once done you should now be seeing the Welcome Screen. Once there navigate to Utilities-Termi